99 not categorized PORSCHE 924S EMBLECan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1987-91 (includes uncategorized and accessory items) FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,194.50
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$254.10
Make a selection 99312301452ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turbocharger. After receiving y...(choose a part on the right to read more)
$2,194.50
Make a selection FVD123011Y These actuators are assembled with springs for higher boost levels. Additional springs are available for tuning to custom boost level. These replacement actuators are supplied complete with brackets ready to install.
$33.00
Make a selection 92860206019 8mm set comes complete with spark plug wires, resistor ends, air boots and coil wires assembled and ready for installation. View/Change Diagram
From $296.96
Make a selection 0057470 This schley brothers original tool has been designed to allow removal and installation of valve springs while the engine is both fully assembled and still in the car. It is professionally made of high quality materials to handle not only stock springs but the pressures of all high performance springs.
$158.00
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96434101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 93060610500ATK The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, clean, degrease and rebuild to factory specifications. Remanufacturing is done in Germany, so the lead times can vary. Send us your original warmup regulator and we will have it remanufactured for you. We do not offer a core exchange on this part. Please note: please package your part as carefully as possible to ensure that damage is not caused en route to us.
$744.70
Make a selection WC101 2.75 inch (69.85mm) diameter. Colorful set of four fit perfectly onto the top of the wheel center cap. Sold as a set of four. General FitmentALL
$29.99
Make a selection
$5.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |